Voopoo Vinci Spark100 Vape Kit

The Voopoo Vinci Spark100 Vape Kit is a compact sub ohm box mod built for vapers who want power and control. It runs on a single 18650 battery, which is sold separately, and delivers a 5 to 100 watt output. As a result, you can dial the power to suit each coil and mood.

In the box you also get a 2ml Uforce-X Nano tank and two PnP X coils. The 0.3 Ohm and 0.6 Ohm coils then cover both MTL and RDTL vaping. Meanwhile, a USB-C cable is included, so you can charge and go straight away.

At a Glance

• Runs on a single 18650 battery, sold separately
• 5 to 100 watt variable output
• Fast 2A charging over USB-C, cable included
• Smart, RBA and Eco modes
• Uforce-X Nano 2ml tank with top filling
• Two PnP X coils included, 0.3 Ohm and 0.6 Ohm
• MTL and RDTL draw styles
• Adjustable airflow for a tuned draw

Who is the Vinci Spark100 for?

Choose the Vinci Spark100 if you want a pocket sized mod with plenty of power. Its 5 to 100 watt range and PnP X coils suit both tighter MTL and airy RDTL draws. Because a single 18650 cell drives it, you can also carry a spare and swap on the go.

Smart Mode keeps setup simple, so newer sub ohm vapers can start quickly. However, if you prefer a built in battery and no loose cells, a beginner vape kit may suit you better. Cloud chasers who want more headroom can instead browse our wider sub ohm vape kit range.

Compact Looks, Solid Feel

The Vinci Spark100 keeps a slim, boxy shape that sits easily in the hand. At 141mm tall and 153g, it feels pocket friendly rather than bulky. A round control button sits on the front, above two smaller adjustment keys.

The finish also carries a sparkling, textured panel that catches the light. Six colourways then make up the range, so there is a look for most tastes:

• Orange-Red Gradient
• Rose Red
• Blue
• Silver
• Metal Gray
• Black

Single Cell Power and Modes

A single 18650 battery powers the Vinci Spark100, and it is sold separately. Therefore, you will need a compatible cell and, ideally, an external charger. Once fitted, the mod pushes a 5 to 100 watt output for warm, full draws.

Three modes then shape each session. Smart Mode reads your coil and sets a safe wattage for you. RBA Mode instead lets you raise or lower the power by hand, while Eco Mode trims wattage to stretch battery life. When the cell runs low, USB-C 2A charging tops it back up.

Uforce-X Nano Tank and PnP X Coils

The included Uforce-X Nano holds 2ml of e-liquid and fills from the top. Twisting off the cap therefore gives quick access to the fill port. It runs mesh PnP X coils, which heat liquid fast for stronger flavour.

Two coils come supplied, a 0.3 Ohm and a 0.6 Ohm, both shown in the table below. The tank also accepts the wider PnP X range, so you can fine tune the draw. For the best results, pair the 0.3 Ohm coil with a 70% VG e-liquid, and the 0.6 Ohm coil with a 50% VG blend. When a coil tires, fresh Voopoo replacement coils drop straight in.

Tune Your Draw

An airflow ring sits at the base of the Uforce-X Nano. Open it up for an airy, restricted direct to lung hit with bigger clouds. Close it down instead for a tighter mouth to lung pull.

Because the coils swap out too, one kit can move between styles. The 0.6 Ohm coil suits a firmer MTL draw, while the 0.3 Ohm coil leans towards warm RDTL clouds. In short, a single setup then covers several vaping styles.

What's in the Box

• 1 x Voopoo Vinci Spark100 mod
• 1 x Voopoo Uforce-X Nano 2ml tank
• 1 x 0.3 Ohm Voopoo PnP X coil
• 1 x 0.6 Ohm Voopoo PnP X coil
• 1 x Glass tube replacement
• 1 x Silicon rubber pack
• 1 x USB-C cable
• 1 x User manual
• Note: an 18650 battery is sold separately