Voopoo Drag X3 Pod Kit

The Voopoo Drag X3 is a refillable sub ohm pod kit for vapers who want mod-level power in the hand. A single 18650 or 21700 battery drives it, so the cell is sold separately. On top of that, the 5W to 80W output covers gentle draws and bigger clouds alike. A full touchscreen also keeps every setting clear at a glance.

In the box you get one PNP X DTL pod and two PNP X mesh coils, in 0.15 Ohm and 0.3 Ohm. Because the pod is built for direct to lung vaping, it suits high VG e-liquid. However, it also handles RDTL and MTL styles. As a result, one kit covers several ways to vape.

At a Glance

• Powered by a single 18650 or 21700 battery, sold separately
• 5W to 80W adjustable output
• DTL, RDTL and MTL vaping
• Button-activated firing
• Smart, RBA and Eco modes
• Full colour touchscreen display
• 2ml side-filling PNP X pod, refillable
• Adjustable airflow, pairs with high VG e-liquid

Who is the Voopoo Drag X3 for?

Choose it if:

• You want a sub-ohm pod kit with single-battery power for daily DTL vaping
• You already own 18650 or 21700 cells and want to put them to use
• You like to shape the draw with adjustable airflow

Look elsewhere if:

• You want a tight, cigarette-like draw: a mouth to lung pod kit fits better
• You would rather not buy a battery separately: a built-in pod kit keeps things simpler

A Single-Battery Mod in the Hand

The Drag X3 keeps the bold, boxy shape the Drag line is known for. It measures 133 by 35 by 27mm and weighs 160g. So it feels solid rather than pocket-slim. A full colour touchscreen also gives it a sporty, premium look. As the successor to the Voopoo Drag X, it adds that touchscreen and a wider output range.

The range spans ten finishes, from stealthy to bright. In short, there is a look for most tastes:

• Spray Black, Carbon Fiber Black and Gray Metal for a clean, understated feel
• Sky Blue, Lake Green and Moss Green for a cooler, fresher accent
• Aurora Purple, Cherry Pink, Glow Pink and Champagne Golden for a bolder finish

Bring Your Own Battery

The Drag X3 runs on a single 18650 or 21700 cell, which you buy separately. Because you can swap in a charged cell, you are never tied to a socket. Meanwhile, the 5W to 80W range gives you room to dial in the vape you want.

Control stays simple too. First, press the button to fire. Then use the touchscreen to switch modes. Smart Mode reads the coil and sets the wattage for you. RBA Mode hands you manual control instead, while Eco Mode stretches each charge further. A USB-C cable is also included, so you can charge the fitted cell in the device.

PNP X Pods and Coils

The kit uses the 2ml PNP X DTL pod, which fills from the side. First, lift the rubber stopper, then top it up and press it back. Two PNP X mesh coils come included, a 0.15 Ohm and a 0.3 Ohm. Because both are made for sub ohm vaping, pair them with a 70% VG e-liquid for the smoothest results.

The pod also works across the wider PNP X range. So you can fit a fresh PNP X pod when yours wears out. Each coil runs best at its own wattage, shown in the table below.

Adjustable Airflow for Every Style

The Drag X3 gives you real control over the draw. First, turn the airflow ring on the pod to tighten or open each inhale. So you can set an airy DTL draw for clouds. Then close it down for a tighter RDTL or MTL feel.

Because the airflow adjusts freely, one device covers several styles. For example, open it up with the 0.15 Ohm coil for big clouds. Then switch to the 0.3 Ohm coil and a tighter setting for a more discreet vape.

What's in the Box

• 1 x Voopoo Drag X3 mod
• 1 x 2ml PNP X DTL replacement pod
• 1 x 0.15 Ohm PNP X DTL mesh coil
• 1 x 0.3 Ohm PNP X DTL mesh coil
• 1 x PNP X platform card
• 1 x USB-C charging cable
• 1 x User manual
• Note: the 18650 or 21700 battery is sold separately