Which devices take the Zeus Z coils?

They fit the GeekVape Zeus sub-ohm tank and the Aegis Legend 2 kit that runs it. Any resistance in the range seats and fires the same way, so if your device uses the Z-series coil, you are choosing purely by the draw and wattage you prefer rather than by fit.

Which resistance and wattage should I pick?

All four are direct-to-lung mesh coils. The 0.15 ohm runs 70 to 85W and the 0.2 ohm 70 to 80W for warm, airy clouds; the 0.25 ohm sits at 45 to 57W and the 0.4 ohm at 50 to 60W for a leaner draw at lower power. Start low and build up.

What e-liquid works best with them?

High-VG e-liquid of 60% VG or above suits every coil in the range. That thicker liquid wicks steadily through the Kanthal mesh at sub-ohm power and keeps the vapour clean, whereas a thinner high-PG liquid can wick too fast and risk a dry hit on these resistances.

How do I stop a new coil tasting burnt?

Prime it before the first draw. Put a few drops of e-liquid onto the exposed cotton, fit the coil, fill the tank, then leave it a couple of minutes so the wick soaks fully. Starting at the lower end of the coil's wattage while it beds in also helps avoid a scorched taste.

GeekVape Zeus Z Replacement Coils

Checking prices...

£10.99

Brand

Geek Vape

Made In

China

Pack Size

5 Pack

Coil Type

Mesh

Coil Resistance

0.15Ω, 0.2Ω, 0.25Ω, 0.4Ω

Choose Flavour

Please select a flavour to continue

Product Summary

GeekVape Zeus Z replacement coils are mesh sub-ohm vape coils for the GeekVape Zeus tank and Aegis Legend 2 kit, supplied in a pack of 5. Every resistance in the range (0.15, 0.2, 0.25 and 0.4 Ohm) is built for direct to lung vaping, with the 0.2 Ohm running at 70 to 80W and the 0.4 Ohm at 50 to 60W. The Kanthal mesh build heats evenly, and the quick-change prebuilt system means a coil swap takes seconds. Use them with high VG e-liquid of 60% VG or above for the cleanest flavour and biggest clouds.

GeekVape Zeus Z replacement coils are prebuilt mesh coils for sub-ohm, direct-to-lung vaping, supplied five to a pack. Each one uses a quick-change design that drops straight into the tank, and the Kanthal mesh build heats the e-liquid evenly across a wide surface for steady flavour and vapour. Four resistances cover the range, so you can restock the exact coil your setup runs.

Which tanks and kits do these fit?

The Zeus Z coils are built for the GeekVape Zeus sub-ohm tank and the GeekVape Aegis Legend 2 kit that uses it. If your device takes the Z-series coil, any resistance in this range will seat and fire the same way, so choosing a coil is a question of the draw and wattage you want rather than fit.

Coil options and the draw each suits

Every coil in the range is a mesh build tuned for direct-to-lung clouds, with the resistance setting how much power it wants:

0.15 ohm: runs 70 to 85W for warm, airy DTL clouds.
0.2 ohm: runs 70 to 80W, a touch cooler while still cloud-focused.
0.25 ohm: runs 45 to 57W for a more measured DTL draw at lower power.
0.4 ohm: runs 50 to 60W, the tightest of the four with a leaner vapour output.

All four favour high-VG e-liquid of 60% VG or above, which wicks well through the mesh and keeps the clouds clean.

Fitting and care

Drop a fresh coil into the tank, then prime it before use: add a few drops of e-liquid onto the exposed cotton and let a filled tank stand for a couple of minutes so the wick saturates. That soak is what prevents a dry, burnt first draw. Start at the lower end of the coil's wattage and work up to taste. When the flavour dulls or takes on a scorched edge, fit the next coil from the pack.